About: Metacrylics
Home Application Specs and Data Warranty Order Links Site Map
  

Metacrylics


Product Data sheets
Roofing & waterproofing test data
Asphalt driveway sealer test data
ICC-ES (ICBO) report
Underwriters Laboratories listing
Material Safety Data sheets
 > Acrylic Base Material Safety Data Sheet
 > Acrylic Black Primer Material Safety Data Sheet
 > Acrylic Clear Primer Material Safety Data Sheet
 > Acrylic Color Material Safety Data Sheet
 > Acrylic White Material Safety Data Sheet
 > Acrylic Gel Material Safety Data Sheet
 > Acrylic Clear Sealer Material Safety Data Sheet
 > Acrylic Plastic Sealer/Crack Filler Material Safety Data Sheet
 > Stitchbonded Polyester Fabric



MATERIAL SAFETY DATA SHEET
Product Name: ACRYLIC COLOR
Product Use: Protective / Decorative Coating
Common Name: Aqueous Pigmented Acrylic Coating


SECTION I:  Manufacturer Information
Manufacturer Name: Metacrylics
Address: 142 N. 27th Street
San Jose, CA 95116
Emergency: (408) 280-7733   Mon - Fri / 9am - 4pm
(408) 280-6329   Fax


SECTION II:  Hazardous Ingredients/Identity Information
Ingredient(s) WT.% CAS # Exposure Limits in Air
ACGIH (TLV) OSHA Other
 EthyleneGlycol 2.2 107-21-1 50 ppm 50 ppm None
 Titanium Dioxide 5.6 13463-67-7 10 mg/m3
(Dust)
15 mg/m3
(Dust)
None
 Zinc Oxide 3.6 1314-13-2 10 mg/m3
(Dust)
15 mg/m3
(Dust)
None
 Acrylic Emulsion 337.8 N/A None None None
 Calcium Carbonate 35.7 471-34-1 10 mg/m3
(Dust)
15 mg/m3
(Dust)
None
 Ammonia 0.01 7664417 25 ppm
(TWA)
50 ppm 50 ppm
NIOSH(REL)


SECTION III:  Physical/Chemical Characteristics
Boiling Point: 100 C Specific Gravity: 1.15 - 1.20
Vapor Pressure: 17.0 at 20 C Melting Point: N/A
Vapor Density: <1,Water Evaporation Rate: Equals Water
Solubility in Water: Miscible Boiling Point: 100 C
Odor And Appearance: Milky gray liquid, mild ammonia odor


SECTION IV:  Fire and Explosion Hazard Data
Flammability: Non-flammable
Autoignition Temp: N/A UEL (% vol): N/A  
Flash Point: N/A LEL (% vol): N/A  
Extinguishing Media: Water, Carbon Dioxide
Special Fire Fighting
Procedures:

None
Unusual Fire & Explosion
Hazards:

Material can splatter above 100 C, dry polymer can burn.
Hazardou Combustion
Products:

May generate carbon dioxide, monoxide, smoke


SECTION V:  Reactivity Data
Stability: Stable          Hazardous Decomposition: None
Incompatibility: N/A          Hazardous Polymerization: Will not occur
Oxidizer: No Reactivity: None
Conditions to Avoid: N/A


SECTION VI:  Health Hazard Data
Skin Contact: Repeated exposure and washing may irritate the skin.
Eye Contact: Liquid, mists and vapors can irritate the eyes.
Inhalation: Mists and vapors developed during spray application may cause upper respiratory irritation.
Ingestion: May cause dizziness, nausea and abdominal pains.
Carcinogenicity: Not considered a carcinogen by IARC, NTP or OSHA.
Other: Contains Ethylene Glycol. Extreme exposures to mists, vapors, or ingestion of large amounts cause liver, kidney, red blood cell damage or central nervous system depression.

FIRST AID PROCEDURES:
Skin Contact: Wash skin thoroughly with a mild soap and water. Consult a doctor if irritation develops.
Eye Contact: Flush eyes fully with clean water. Consult doctor if irritation develops.
Inhalation: Remove to fresh air. Apply artificial respiration if patient is not breathing. Get immediate medical attention.
Ingestion: If conscious, give victim 2 glasses of clean water and induce vomiting by placing a spoon or finger at the back of the throat. Do not give anything to an unconscious or convulsing person. Get immediate medical attention.


SECTION VII:  Precautions for Safe Handling and Use
In Case of
Spill or Leak:
Keep spectators away. Floor may be slippery. Contain spill with inert material or absorbent. Do not allow to enter drain or waterways. Transfer liquid material to containers for recovery or disposal and solid containment material to separate containers for disposal.
Disposal: Absorb materials with an inert absorbent material and place in sealable containers. Landfill the solids and contaminated containment materials according to local, state and federal regulations.
Note: Dispose of contaminated product and materials used for clean-up in a manner approved by local, state or federal laws and regulations.


SECTION VIII:  Control Measures
Ventilation: General ventilation is normally adequate.
Respiratory: If use conditions create vapors or mists, or limited ventilation is available, a NIOSH approved organic vapor mask with a dust/mist pre-filter is advocated.
Clothing: Long sleeved cover-alls, rubber gloves and safety shoes are recommended.
Eyes: Goggles are recommended for spray application.
Other: Wash hands and face thoroughly before eating or handling food.


PREPARATION OF MATERIAL SAFETY DATA SHEET:
Prepared By: Instant Asphalt, Inc.
Date: April 6, 2004


 


FeaturesApplicationSpecs and DataWarrantyOrderLinksSite Map